Latest news: --- ap200 activate --- sdp3 update 2.42.2 --- I sell solution convert to AMG w222 Prefacelift and Facelift and w213 - w464 --- BEARING MANUAL - SKF --- Suzuki SDT-II Smart Diagnostic Tester v2.23.0.18 --- ISTA-D 4.21.25 Standalone / BLP / SQLiteDBs --- VAG, Mercedes Teile Steuergeräten. --- Renault Can Clip 193 - Torrent (without pass) --- Need manuals for opel insignia all releases --- I need online account for repair --- BEARING MANUAL - SKF --- PET2 Update 5410 Multilingual is availeble --- Carly v42.03 PRO (All Brands) FULL - Unlocked --- Remote Install - Nissan Consult III, Fast, Diesel UD EPC, Forklift, NERS --- AGCO - Good truck diagnostics device with European Union quality --- Autocom orginal cdp+ --- Caterpillar SIS Full 2019-07 installation --- POPULAR RANGE OF SKF BEARINGS - PART II --- New STILL STEDS Navigator Forklifts Ver. D8.19 R2 + Activation license Key --- VAS 5052A Recovery DVD ---
  

Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
GM MDI 2 Damaged - component missing
#1
Hello
Need help. have a GM MDI2 DAMAGED that. After checking I have found that a component is missing. Component missing at T3. Can irdendjemand tell me or send photo which component is missing there and how it has to be mounted. thank you for your help


Attached Files Thumbnail(s)
           
Reply
Thanks given by:
#2
(12-08-2019, 11:30 AM)werner5395 Wrote:  Hello
Need help. have a GM MDI2 DAMAGED that. After checking I have found that a component is missing. Component missing at T3. Can irdendjemand tell me or send photo which component is missing there and how it has to be mounted. thank you for your help



I have had problems with mdi 1 more than once. Problems are the two most commonly encountered:
The usb cable is weak or plugged in (device socket outlet) and secondly when you connect two wires the most common problem is steer pins should refresh them.
regards
ibi1961
Reply
Thanks given by:
#3
Does anyone have a picture of the board or the missing part?
Thank you
Reply
Thanks given by:
#4
(12-09-2019, 08:52 AM)werner5395 Wrote:  Does anyone have a picture of the board or the missing part?
Thank you

hallo i have no pictures since repairing my MDI ......... the question is does the computer see the MDI is connected with USB Cable ??
Reply
Thanks given by: Administrator
#5
no - no comunikation with computer- the missing part goes to usb
Reply
Thanks given by:
#6
(12-11-2019, 10:29 AM)werner5395 Wrote:  no - no comunikation with computer- the missing part goes to usb

Hallo Werner did you try to replace Cable ?? Try holding the cable left or right up or down with the USB port on the MDI and plug it into the leptop 99% with your other hand so that the leptop can see the device.
Reply
Thanks given by: Administrator
#7
yes i have try with new cabel- usb conector is new- problem is missing component-
Reply
Thanks given by:
#8
(12-13-2019, 09:44 AM)werner5395 Wrote:  yes i have try with new cabel- usb conector is new- problem is missing component-

Hallo werner when you connect MDI to 12 V can the device light up and do the procedure ??? if it turns on then the problem in Figure 2 is the white con- nectors where you connect the device ........ if it does not receive the 12 V signal then the problem is 90% on the connectors coming out of the stacker where the cable for the obd2 is connected
mfg
ibi19161
Reply
Thanks given by: Administrator


Forum Jump:


Users browsing this thread: 1 Guest(s)